The Forge RAMPAGE Dual 0,14 Ohm - Charro Coils

Charro Coils Charro Coils

New product

The Forge RAMPAGE Dual 0,14 Ohm - Charro Coils Expand

Prebuilt Coils The Forge Rampage Dual 0,14 Ohm - Charro Coils

Experience the genuine Prebuilt Coils The Forge Rampage Dual 0,14 Ohm by Charro Coils. This pack brings you 2 handcrafted coils, tailored for an enhanced vaping encounter. Precision-made and with a passion, they deliver unmatched performance in your electronic cigarette. Purchase and take your vaping ritual to new heights.

The Forge Charro Coils


More details

Available for immediate delivery

11,90 €

By buying this product you can collect up to 1 loyalty point. Your cart will total 1 point that can be converted into a voucher of 0,10 €.

The Forge Rampage Dual 0,14 Ohm (Pack 2)


0.14 ohm/dual coil - 0.28 ohm/single coil


CharroCoils handmade coils in Spain and Europe
by Charro Coils


The Forge RAMPAGE offers excellent performance and instant response.


The Forge Rampage coils are born from the idea of ​​creating a very versatile model, which adapts to any dual coil, RDA, RTA or RDTA atomizer without any problem, being able to use them in atomizers from 28mm to 23mm with a total guarantee that the performance will be optimal.

After four years of dedication to the elaboration of artisan coils, The Forge was born.

Throughout this time, Charro Coils has been learning the trade, always worrying about offering customers the best.

Today, four years later and after more than 100,000 pairs of coils manufactured, they present The Forge, handcrafted coils that border on perfection, both in design and presentation, as well as in the use of the most recognized materials on the market.

They work perfectly with all RBA atomizers.


The Forge RAMPAGE Coils Features:

Inner diameter: 2.50mm

Made with Nichrome 80

Resistance value: 0.14 ohm / dual coil - 0.28 ohm / single coil

* Pack 2 units


The Forge Charro Coils


* Important tips for repairable coils:


When you unpack the coil, place it on a guide of the indicated diameter, insert the legs of the coil into the hole of the atomizer deck, one leg on the positive pole and another on the negative pole.

Adjust the position of the coil in place and tighten the screws, finally, cut the excess.

Once installed make sure that it does not touch the coil with any metal part of the atomizer to avoid short circuits.

When we have them installed, we will proceed to stabilize it. This process has to be carried out in an electronic device, never in a mechanical mod. To start stabilizing the coils, select a low power output voltage in the electronic device, around 1.8V. Little by little we will give short presses until we see that the coil is picking up temperature. Without ever putting the coil completely incandescent, we will glimpse, a series of points that light up more than the rest of the coil. To eliminate these points and that the coil is properly stabilized, we will tighten the turns of the coil with ceramic tweezers, gently and slowly until they have been completely removed.

Once there are no red dots and the coil ignites evenly from the center to the ends, we are ready to start using it and just need to put the cottonplace it correctly and add the liquid.



When we see that the coil is dirty or that the cotton has lost some of its properties, we will remove the cotton and repeat the process of stabilizing the coils, but in a much softer way, never turning them red hot. We will heat them calmly and before they become incandescent we will clean them with a metal brush, we will repeat this process two or three times in each cleaning, when they are already clean of the largest remains, we will reheat them and submerge them hot in a glass of water to temper them and that there is a cleaning in the coil by pyrolysis until it is perfectly clean.

Then, we will put the cotton and the liquid back.

The duration of the coils depends largely on the proper maintenance and aggressiveness of the liquids we use when vaping.

Safety and use warnings:

All coils work perfectly in both electronic mods and mechanical mods.

Electronic mods: You have to be always attentive in case you have been able to leak some liquid in the electronics, keep the mod clean and always use batteries with high discharge amperage and in good condition.

Mechanical mods: This is where more emphasis needs to be made on safety. It is essential that the mod is always clean, without bumps and with all the pieces that compose it correctly placed. When mechanical devices are used, ALWAYS use batteries with the maximum possible discharge amperage.


The Forge Charro Coils

The Forge Charro Coils

Write a review

Charro Coils in Vapvip Europe, Spain


18 años

Only for over 18 years old. 

We use cookies to enhance your navigation experience. Consult our PRIVACY POLICY PAGE