Spirit Coils The Purge Coils 0,60Ohm - Spirit Coils

No Stock Vaper Products No Stock Vaper Products

New product

Spirit Coils The Purge Coils 0,60Ohm - Spirit Coils Expand

Prebuilt The Purge Coils 0.60 Ohm (Pack 2) - Spirit Coils

Enjoy the latest generation The Purge Coils 0.60 Ohm (Pack 2) manufactured in Spain. Inner diameter: 3,0mm. Manufactured Nichrome 80 of the highest quality. Coil value: 0,60 Ohm. HANDMADE COILS available to buy in Vapvip, your vaping shop in Spain.

Spirit Coils in Vapvip Europe, Spain

More details

Out of Stock

18,90 €

By buying this product you can collect up to 1 loyalty point. Your cart will total 1 point that can be converted into a voucher of 0,10 €.

Prebuilt The Purge Coils 0.60 Ohm (Pack 2)

by Spirit Coils


Specially designed to vape in Stacked.

Designed as single coil at 0.60 ohms and dual coil 0.30 ohms. 3mm diameter with 9 turns.

Inner diameter: 3,0mm

Made with Nichrome 80

Coil Value: 0,60 Ohms.


 *Pack 2 units


* Important tips for repairable coils:


When you unpack the coil, place it on a guide of the indicated diameter, insert the legs of the coil into the hole of the atomizer deck, one leg on the positive pole and another on the negative pole.

Adjust the position of the coil in place and tighten the screws, finally, cut the excess.

Once installed make sure that it does not touch the coil with any metal part of the atomizer to avoid short circuits.

When we have them installed, we will proceed to stabilize it. This process has to be carried out in an electronic device, never in a mechanical mod. To start stabilizing the coils, select a low power output voltage in the electronic device, around 1.8V. Little by little we will give short presses until we see that the coil is picking up temperature. Without ever putting the coil completely incandescent, we will glimpse, a series of points that light up more than the rest of the coil. To eliminate these points and that the coil is properly stabilized, we will tighten the turns of the coil with ceramic tweezers, gently and slowly until they have been completely removed.

Once there are no red dots and the coil ignites evenly from the center to the ends, we are ready to start using it and just need to put the cottonplace it correctly and add the liquid.



When we see that the coil is dirty or that the cotton has lost some of its properties, we will remove the cotton and repeat the process of stabilizing the coils, but in a much softer way, never turning them red hot. We will heat them calmly and before they become incandescent we will clean them with a metal brush, we will repeat this process two or three times in each cleaning, when they are already clean of the largest remains, we will reheat them and submerge them hot in a glass of water to temper them and that there is a cleaning in the coil by pyrolysis until it is perfectly clean.

Then, we will put the cotton and the liquid back.

The duration of the coils depends largely on the proper maintenance and aggressiveness of the liquids we use when vaping.

Safety and use warnings:

All coils work perfectly in both electronic mods and mechanical mods.

Electronic mods: You have to be always attentive in case you have been able to leak some liquid in the electronics, keep the mod clean and always use batteries with high discharge amperage and in good condition.

Mechanical mods: This is where more emphasis needs to be made on safety. It is essential that the mod is always clean, without bumps and with all the pieces that compose it correctly placed. When mechanical devices are used, ALWAYS use batteries with the maximum possible discharge amperage.


Spirit Coils in Vapvip Europe, Spain

Write a review

Productos de vapeo fuera de stock


18 años

Only for over 18 years old. 

We use cookies to enhance your navigation experience. Consult our PRIVACY POLICY PAGE